Acta Scientific Dental Sciences (ISSN: 2581-4893)

Research Article Volume 4 Issue 2

Accuracy and Reliability of CBCT Scan in Obtaining Digital 3D Model from Dental Plaster Model for Orthodontic Space Analysis: Diagnostic Accuracy Study

Sara Alaa El-din1*, Farid Medhat2 and Hossam Kandil3

1B.D.S, Faculty of Dentistry, Cairo University, Egypt
2Associate Professor of Oral and Maxillofacial Radiology, Faculty of Dentistry, Cairo University, Egypt
1Professor of Oral and Maxillofacial Radiology, Faculty of Dentistry, Cairo University, Egypt

*Corresponding Author: Sara Alaa El-din, B.D.S, Faculty of Dentistry, Cairo University, Egypt.

Received: December 09, 2019; Published: January 03, 2020

×

Abstract

Objective: This study was conducted to evaluate accuracy of CBCT derived digital models in terms of linear measurements compared to direct measurements on dental plaster models for orthodontic space analysis.

Methods: 16 plaster models were digitized using Planmeca Promax 3D mid CBCT machine and 28 anatomical landmarks were identified on both the plaster models and their digital counterparts. Linear measurements were taken for the inter-molar, inter-canine and mesio-distal teeth width on plaster models using digital caliper and they were considered as the gold standard in the study. Then, the same measurements were taken on digital models using third party software (In Vivo 5.3.1 Dental Software) for comparison.

Results: The statistical analysis of the recorded measurements showed a mean value of 0.14 mm (SD. 0.34) for the inter-molar width, 1.55 mm (SD. 4.03) for the inter-canine width and 0.11 mm (SD 0.1) for the mesio-distal teeth width. There was neither statistical significant nor clinical relevant difference regarding the inter-molar width. On the contrary, the mesio-distal teeth width showed statistical significant difference yet, this difference did not translate to clinical relevance. Finally, the inter-canine width showed a non-statistically significant difference which did translate to clinical relevance.

Conclusion: CBCT derived digital models provide accurate and reliable linear measurements for orthodontic space analysis except for the inter-canine width measurements.

Keywords: CBCT; Digital Models; Plaster Models; Orthodontic Space Analysis; Linear Measurements

×

References

  1. Rossini G., et al. “Diagnostic accuracy and measurement sensitivity of digital models for orthodontic purposes: a systematic review”. American Journal of Orthodontics and Dentofacial Orthopedics 149.2 (2016): 161-170.
  2. Kumar AA., et al. “Digital model as an alternative to plaster model in assessment of space analysis”. Journal of Pharmacy and Bioallied Sciences 7.2 (2015): S465.
  3. Rischen RJ., et al. “Records needed for orthodontic diagnosis and treatment planning: a systematic review”. PLoS one 8.11 (2013): e74186.
  4. White AJ., et al. “Analysis of intra-arch and interarch measurements from digital models with 2 impression materials and a modeling process based on conebeam computed tomography”. American Journal of Orthodontics and Dentofacial Orthopedics 137.4 (2010): 456.e1- 456.e9.
  5. Radeke J., et al. “Vergleichbarkeit der Erfassung metrischer Werte an konventionellen Gipsmodellen und 3-D-Scans”. Journal of Orofacial Orthopedics 75.4 (2014): 264-274.
  6. Sousa MV., et al. “Accuracy and reproducibility of 3-dimensional digital model measurements”. American Journal of Orthodontics and Dentofacial Orthopedics 142.2 (2012): 269-273.
  7. Joffe L. “Ortho CAD: digital casts for a digital era”. Journal of Orthodontics 31 (2004): 344-347.
  8. Wiranto MG., et al. “Validity, reliability, and reproducibility of linear measurements on digital models obtained from intraoral and cone-beam computed tomography scans of alginate impressions”. American Journal of Orthodontics and Dentofacial Orthopedics 143.1 (2013):140-147.
  9. Becker K., et al. “Accuracy and eligibility of CBCT to digitize dental plaster casts”. Clinical Oral Investigations 22.4 (2018): 1817-1823. 
  10. El-Zanaty HM., et al. “Three-dimensional dental measurements: An alternative to plaster models”. American Journal of Orthodontics and Dentofacial Orthopedics 137.2 (2010): 259-265.
  11. Lippold C., et al. “Methodological accuracy of digital and manual model analysis in orthodontics - A retrospective clinical study”. Computers in Biology and Medicine 62 (2015): 103-109.
  12. Şakar T., et al. “Assessment of the accuracy of orthodontic digital models”. Eurasia Journal of Mathematics Science and Technology Education 13.8 (2017): 5465-5473.
  13. Bariar A., et al. “Validity and Reproducibility of Digital Models Obtained by Cone Beam Computed Tomography Imaging”. Journal of Clinical and Diagnostic Research 12.9 (2018).
×

Citation

Citation: Sara Alaa El-din., et al. “Accuracy and Reliability of CBCT Scan in Obtaining Digital 3D Model from Dental Plaster Model for Orthodontic Space Analysis: Diagnostic Accuracy Study”.Acta Scientific Dental Sciences 4.2 (2020): 01-04.



Member In






News and Events


  • Certification for Review
    Acta Scientific certifies the Editors/reviewers for their review done towards the assigned articles of the respective journals.
  • Submission Timeline for March Issue
    The last date for submission of articles for regular Issues is March 15, 2020.
  • Publication Certificate
    Authors will be issued a "Publication Certificate" as a mark of appreciation for publishing their work.
  • Best Article of the Issue
    The Editors will elect one Best Article after each issue release. The authors of this article will be provided with a certificate of “Best Article of the Issue”.
  • Welcoming Article Submission
    Acta Scientific delightfully welcomes active researchers for submission of articles towards the upcoming issue of respective journals.
  • Contact US